I/O Frames can be used to physically locate inputs and outputs connections near their sources and destinations. Dual Gigabit Ethernet connections route the audio signals through the Core for processing.
Each I/O Frame can house up to four I/O cards enabling up to 16 channels of input and/or output in a single unit.
Microphone/Line level input card:
- 4 channels
- Greater than 112 dB dynamic range
- Less than 0.004% THD+N
- Phantom power (configured via software)
Line level output card:
- 4 channels
- Greater than 112 dB dynamic range
- Less than 0.004% THD+N
QSC DataPort I/O and instrumentation card:
- 4 channels
- Greater than 114 dB dynamic range
- Less than 0.004% THD+N
- Supports dataport amplifiers (CX, PowerLight, PL2, PL3, DCA)
AES/EBU input/output card:
- 4 x 4 Digital audio channels
- Frequency Response +/- 0.2 dB
- 4 connectors
| Audio Flex Channel Capacity | 8 |
| Audio Flex Channel Assignments | Each channel can be configured as a mic/line input or as a line output (configured through Q-SYS Designer software) |
| Rear Panel Indicators | “Link”, “Speed” and “Activity” LEDs on all LAN ports |
| USB Inputs & Outputs | |
| USB Audio Bridging | Up to 8×8 channels of digital audio in/out via software definable USB instances advertised to the USB Host operating system |
| USB B (device port): | Bit depth: 16-bit, 24-bit (configured in Q-SYS Designer software) |
| USB Channel Capacity: 8×8 | |
| Sample Rate: 48kHz | |
| Controls | |
| Front Panel Controls | “NEXT” OLED page forward capacitive touch button |
| “ID” device identification capacitive touch button | |
| “Clear Network Settings” - invoked when “NEXT” and “ID” are pressed simultaneously | |
| Front Panel Connectors | AUX USB: USB Host × 2 (Type A connectors) |
| Rear Panel Connectors | Audio Flex I/O: 12-pos blue Euro Block × 2 |
| GPIO: 10-pos black Euro Block × 2 (GPI = 1x10, GPO = 1x10) | |
| RS232: 3-pos black Euro Block | |
| AUX USB Host: USB Host × 2 (Type A connectors) | |
| AUX USB Device: USB Device Port (Type B connector) | |
| Media Network LAN A/PoE+ Power In : RJ45 1000 Mbps | |
| Media Network LAN B: RJ45 1000 Mbps | |
| AUX PWR In: 2-pos green Euro block | |
| GPIO | |
| General Purpose Inputs | 0-24VDC analog input or contact closure |
| General Purpose Outputs | Open collector, 24VDC at 200mA max, internal pullup to 3.3V |
| GPIO 12 VDC Power Pins | 12VDC out at 100mA max |
| Miscellaneous | |
| PoE+ Power Input | IEEE 802.3at compliant powered device, PoE+ power supplied through LAN A port |
| External Power Input | 24VDC, 1.2A supplied via the external power input, may be used as the primary power source or as a backup to the PoE+ source |
| Regulatory | FCC 47 CFR Part 15 Class A, IC ICES-003, CE (EN55032, EN55035), EU RoHS directive 2011/65/EU, WEEE directive 2012/19/EU, China RoHS directive GB/T26572, EAC, RTL |
| Product Dimensions | 220 × 240 × 44 mm |
| 8.66 × 9.43 × 1.75 in | |
| 1RU half rack | |
| Included Accessories | Connector kit, rack ears, surface mount kit, installation manual, USB cable (Type A to Type B) |
Part Code
QSC I/O Frame
You May Be Interested In
You can manage this carousel from admin.You can stop autoplay, increase/decrease aniamtion speed and number of grid to show and products
Recently viewed product
You can control fully on this carousel from store admin as describe in above section
